icShop Logo
Welcome, ( 登入 or 註冊 )


創客萊吧 MakerLab

USB DC-DC 升壓模組 (0.9V~5V)
$ 18.0 元

5V USB升壓模組(@1000mA from 1.8V+)
售價 : NT$ 660.0 元
製造商 :Adafurit
適用運送方式 : 7-11取貨付款,7-11純取貨,郵寄(單一運費),貨運,宅配,貨到付款,7,8
出貨時程: 【現貨+預購】如遇缺貨,預購交期為4~10個工作天(不含例假日)   

輸入數量 :
Add to wish list
產品上架時間 2015 四月 17 週五.



PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. With a beefy 4A DC/DC converter, it can give you 1A+ from as low as 2V. 

Like our popular 5V 1A USB wall adapter, we tweaked the output to be 5.2V instead of a straight-up 5.0V so that there's a little bit of 'headroom' long cables, high draw, the addition of a diode on the output if you wish, etc. The 5.2V is safe for all 5V-powered electronics like Arduino, Raspberry Pi, or Beagle Bone while preventing icky brown-outs during high current draw because of USB cable resistance.
The PowerBoost 1000 has at the heart a TPS61030 boost converter from TI. This boost converter chip has some really nice extras such as low battery detection, 4A internal switch, synchronous conversion, excellent efficiency, and 700KHz high-frequency operation. Check out these specs!

    • Synchronous operation means you can disconnect the output completely by connecting the ENable pin to ground. This will completely turn off the output
    • 4A internal switch means you can get 1000mA+ from as low as 1.8V, 1500mA+ from 2 NiMH or Alkaline batteries, and at least 2000mA from a 3.7V LiPoly/LiIon battery or 3 NiMH/Alkalines. Just make sure your batteries can actually supply the required 2-4A, OK?
    • Low battery indicator LED lights up red when the voltage dips below 3.2V, optimized for the most common usage of LiPo/LiIon battery usage
    • On-board 1000mA charge-rate 'Apple/iOS' data resistors. Solder in the included USB connector and you can plug in any iPhone or iPod for a speedy 1000mA charge rate. Works with iPads, both mini and 'classic' type.
    • Full breakout for battery in, control pins and power out
    • 90%+ operating efficiency in most cases (see datasheet for efficiency graphs), and low quiescent current: 5mA when enabled and power LED is on, 20uA when disabled (power and low batt LED are off)

Great for powering your robot, Arduino project, single-board-computer such as Raspberry Pi or BeagleBone! Each order comes with one fully assembled and tested PCB, a loose 2-PH JST jack, a 2-pin Terminal block and a loose USB A jack.
If you are powering your project from USB, solder the USB A jack in (a 3-minute soldering task). Then choose either JST for input (JST is often used for our LiIon batteries, but the connector is only rated for 2A) or a terminal block. 
The 1000 version comes with a 2-pin terminal block so you can solder it to the output spot where the USB jack would go. Or don't solder any connectors in for a more compact power pack and go with 22AWG wires soldered directly in.


  • Dimensions: 29mm x 23mm x 2mm / 1.1" x .9" x .1"
  • Height w/ JST: 7.5mm / .30"
  • Weight: 6.0g

Hey there's a typo on the back, it says TPS61090 but we really use the TPS61030 - the '90 is the 2A version, the '30 is the 4A version! We'll fix on the next PCB run. Read more about the TPS61030 boost converter from TI here



U3V50ALV升壓模組 4-12V【限量3個】
IN voltage: 2.9 V to VOUT, OUT4~12V

$ 590.0 元
$ 299.0 元
1 x 'U3V50ALV升壓模組 4-12V【限量3個】'
大功率 5V USB升壓模組@500mA+【限量5個】
$ 749.0 元
1 x '大功率 5V USB升壓模組@500mA+【限量5個】'
XL6009 DC-DC 直流升壓模組
電源模組 輸出可調 超LM2577 最大4A電流
$ 32.0 元
1 x 'XL6009 DC-DC 直流升壓模組'
LM2577大功率DC-DC 升壓模塊
DC-DC升壓模組,穩壓電源模組,IN3.5-30V OUT4-30V帶指示燈

$ 200.0 元
$ 100.0 元
1 x 'LM2577大功率DC-DC 升壓模塊'
FT232 USB UART Board (mini)
$ 220.0 元
1 x 'FT232 USB UART Board (mini)'
聚合物鋰電池-5100mAh 3.7V
鋰電池,可充電電池,Polymer Lithium Ion Battery
$ 280.0 元
1 x '聚合物鋰電池-5100mAh 3.7V'
2017年版 1W 5100mAh 充電供電蓄電套件
Arduino MCU 開發板或各類 USB 小型裝置
$ 680.0 元
1 x '2017年版  1W 5100mAh 充電供電蓄電套件'